FRTS Bandwidth and clock rate
Hi Everyone,I am on Vol. I QoS 10.20 regarding Legacy Frame Relay Traffic Shaping.In the question you ask to configure R1, R2 and R5 physical connection rates with 128Kbps, 384Kbps and 1536Kbps...
View ArticleFabric Path and vPC / vPC+
is it possible to bundle several fabric path links into one portchannel? I have not been able to find any documentation that supports or denies this. Thanks
View ArticleLead time for available seat in RTP?
Is there a way to find out how long is the lead time to get an available lab seat in RTP ? I havent pass the Written as of yet.
View ArticleIS-IS for FabricPath
Hi all,Lets say we have two data center locations and one remote location and MPLS VRF configured between the data centers and the remote location. We use IS-IS as the IGP. Now we want to run...
View ArticleLooking Up stuff on the Doc CD Practice.
In short this is the one part of my prep I have been lazy about, partly because once I finish a task I wanna hurry up and get to the next.However my solution is to take 2 days out at the finish of WB1...
View ArticleAutomatic reply: initial config routers ine workbook vol1
I am currently out of the office returning on Tuesday, July 30th. During my absence I will have limited access to e-mail. If you require technical support, please resend your message to...
View ArticleAutomatic reply: Friday Night Teaser
I am currently out of the office returning on Tuesday, July 30th. During my absence I will have limited access to e-mail. If you require technical support, please resend your message to...
View ArticleTask 10.78 Catalyst 3560 SRR Shaped Mode
Hi, I've been having problems achieving the bw in the different classes as listed in the solution. Also the solutio mentions "The bandwidth guaranteed to AF41 is close to target 500Kbps" but the limit...
View ArticlePrint lab vs PDF lab while studying?
Hello, I have looked around on Cisco's site and I am unable to figure out how the exam is delivered in terms of a pdf or a printed copy? I have been printing out all of my Vol1 INE workbook and I am...
View ArticleCombo Frame Relay Switch / Terminal Server
I'm digging through old hardware at my office that we have retired and trying to cobble together a semi decent Lab for completing my CCNP and then later my CCIE. Going over the INE lab setup I see...
View ArticleAuthoritative DNS Server and DNS server difference?
what is the difference between an Authoritative DNS Server and a DNS server? Thankyou for any clarification. <edit> ok found this answer that makes sense but need a check on IEOC to make sure...
View ArticleFriday Night Teaser
Configure the switches so R5 and R6 can communicate You are not allowed any changes on the routersYou are not allowed to add change or delete any commands on any interface (SVI or physical) on the...
View ArticleLocked out - Help...
Looking for suggestions as I have locked myself out of some kit which is a tad embarrassing. It's the worst time to do it with the weekend just started and noone in the office which is a 2 hour round...
View Article[Success ] CCIE RS written
Hello Community,Just to let you know that I pass written R&S with 916/1000.Next step, first attemp Lab due to December.Thanks to INE and everyone on this community for helping me acheive my...
View Articlesetting default-gateway to own address!
Hi. I don't understand the RS Vol2 > Lab 8 > Task 7.1 .. so what is the meaning of "setting the gateway to their own IP address" ?and for my second question, with regard to the same Lab, Task...
View ArticleRSVP Calculations
I've seen some conflicting information regarding RSVP calculations. On one hand, almost everywhere I check, I see the calculation posted as (N-1)x24+40 for g.729 to include the worst case scenario...
View ArticleRIP vs EIGRP auto-summary behavior
Dear ieoc members and TechEdit TeamIn the Open Lecture about summarization, Brian Mcgahan mentioned that EIGRP and RIPv2 operate a bit differently when auto-summarization is in effect.More...
View ArticleEIGRP and RIP Auto Summary
I've just completed the basic EIGRP config for task 5.1 in Workbook 1. All my devices have received their EIGRP updates and have converged. Auto-summary has been left on.In the solutions there is the...
View ArticlevPC Keepalive over SVI
Hi, last night I was going through some of the DC Nexus Advanced lab workbooks and completed the one for vPC using a L3 SVI as the keepalive. Not a problem with that, my question is in regard to the...
View ArticleSIP Supplementary Service Update CID Message
I'm implementing CUBE, but because I have to send specific ANI's to specific Service Provider SBC's, I'm using "steering codes" prefixed at the beginning of the number to route the call correctly....
View Article