TASK 3.4
3.4. PPP• Configure PPP on the Serial connection between R4 and R5.• Use IP unnumbered for this connection and use the most reliable interface.• Disable /32 prefix generation After using the...
View ArticleStruggle to use this workbook
I am starting wb1 and I find it very frustrating to use and understand. The online format is frustrating because right after the task section, it gives you the answer and there really isnt a way to...
View ArticleMPLS snafu
Doing the lab for OSPF MPLS OSPF CE-PE routing 14.7. I have checked my configs vs. the workbook and everything is working except ONE thing I was trying to change. R5 & R6 are the PE's in the lab....
View ArticleTask 4.11 -- Loop in IGP Redistribution
WB-3 Lab 7 Task 4.11 IGP Redistribution-------------------------------------------------------The solution is not complete. Distance OSPF external 171 This is good to protect external EIGRP...
View ArticleClik here to view.
Manage symmetric routing
Hi, I have a question regarding symmetric routing.As you can see from the picture below, I can easily make routing decision from 50.0.0.0/24 to 30.0.0.0/8 and 40.0.0.0/8 by manipulating the metric when...
View Article2.7 BGP Summarization
In solution, it uses "network 132.1.5.0 mask 255.255.255.0". I think R5 won't send 132.1.0.0/16 to BB2 anymore if F0/0 goes down.Shall we redistribute EIGRP to BGP? In that case, the network enviroment...
View ArticlePolicy Map only matching on the first entry?
Either I am missing something or my config is wrong or it just works that way?I am working on a 3750 switch and trying to police some traffic outbound. There are servers connected downstream of two...
View ArticleCan any one Advise
Hello All,I want to know if any one have done or can adivse that can i use my existing CCIE R&S LAB equipment in the SP as well.I know i do not have XR but i can simulate XR over GNS and connect it...
View ArticleBc and Be Formula
I'm a bit confuse on how to calculate Bc and Be ? And why it arrives to 3200 and 6400? I think I'm lost on Tc value (time) and Te.Per documentation, the Formula is Tc = Bc/CIR and Te=Be/PIRBc = CIR *...
View ArticleEnhanced L2 licence on rack rental N5k's
Unless I am mistaken\being dense or both? the N5k switches in the rental racks don't have enhanced L2 licences. This means no fabric path. can anyone shed any light on this?
View ArticleROUTER ID for OSPF , EIGRP , RIP , BGP
Hi Experts, Pls. share your experience. Is it necessary to configure your router id ( RID ) for your protocols ( OSPF , EIGRP , RIP and BGP ) unless specified to do so in the exam ? Or configure only...
View Article10.27 MQC Peak Shaping
Not sure how it got this value - 64000 6400 6400? thanks Configure R1 and R6 to shape HTTP traffic to a peak rate of 128 Kbps as it is sent out to VLAN 146.Use Bc and Be bursts based on a 10ms...
View ArticleIs anybody preparing DC ccie?
Is anybody preparing DC ccie?I am going to take my lab somedays later. hope to communicate with people who are preparing DC Lab too.
View ArticleTask 5.3 Pim
Im finding the wording of this solution quite difficult to understand. "Configure the RPs so that only sources connected to R3 and R4 areallowed to send multicast traffic streams" From this I got "all...
View ArticleTask 5.2
Is an mroute allowed? is an mroute not the same as a static/default route and not allowed unless otherwise stated?Why does the SG use an added ip address on tunnel 14? again this shouldnt be allowed?
View ArticleTask 8.3
On task 8.3 it says packets marked with a precedence of 3 limited to 1Mbps, normal burst 1500bytes, but doesnt say anything about maximum burst size. Where did they get 2000 from? on the lab exam would...
View ArticleGlobal ACL question
Dears,I was checking the solution of the task "ASA basic access-list" and i was confused about the following:When we apply a global ACL on the ASA and there are no ACLs applied on interfaces, the...
View Articlethe idea of MPLS ? how and why ?
hi allI am still new to MPLS, I like to know the reason of the technology I read before going into the details.As I understand, the idea of MPLS is to forward the traffic based on Labels not IP...
View ArticleIne CCIE SP Labs in dynamips with i5 processor????
Anyone has successfully done running ine ccie SP Labs in dynamips with i5 processor ????
View ArticleAutomatic reply: the idea of MPLS ? how and why ?
I will be out of the office the week of April 14th, returning April 21st, with limited to no access to email. If you need immediate assistance please contact Cliff Wilberding (601.297.6642 or...
View Article