SPAN or RSPAN or some cable loop trick
Hello networkers,I have an ethernet port (Gi0/5 on a cisco switch) on which I receive mirrored traffic (from some non cisco switch). I need this traffic to be tagged and send to a trunk port (Gi0/1 on...
View ArticleClik here to view.
SP Core with IS-IS single topology with MPLS TE
Hello INE Community,If we have a SP core configured with ISIS for both of IPv4 and IPv6 with single-topology.If we have a traffic-eng tunnel configured on a PE, Is it allowed to use "autoroute...
View ArticleCCIE RnS Version Change to 5 by 2013 End ?? Any Information
hello everyone , I just wanna know about the version change of RnS track ??When Cisco will announce & when its gonna change ver 5 ( new bluepint ) What New things are expected to get changed . If...
View ArticleWhich CCIE track is Best for 1st CCIE Exam RnS or DC ?
hello everyone , I m very much confused between the selection for CCIE track I had More Experience on RnS , & r8 now go for CCIE first time .According to expert knowledge & experience which...
View ArticleUCS components overview for beginners along with some peer review.
I have come across a very good blog post about UCS components for absolute begginers.http://storagemojo.com/2010/04/21/a-deep-dive-into-ciscos-ucs/Hope it may help others, will keep updating this post...
View ArticleNAT - ip nat outside source
I came upon some interesting results when I was configuring NAT on my home router to allow Internet access for a Raspberry Pi. I configured the interface connected to the Pi as an ip nat outside...
View ArticleCisco Phone view and Device Profile
Hi all,Is it possible to make ti work? I tried to configure it but it doesn't.Basically the issue is that when i try to associate the device profile to the app user phoneview it fails.Simply when i...
View ArticleBranch 1 Phone Registration Issue
Hi Guys, I always have an issue INE Rack 1 , all the will register except at branch 1 phone its getting IP from DCHP but not able to register with CCM,i have done clear cdp table ,shut and no shut the...
View ArticleVlans and SVI in VPC+ Fabricpath
I have strange issue , dont know what i am missing on this configuration , configured VPC+ between 2 7Ks, configured 2 vlan(vlan 193-195) and there SVI's and configured GLBP and everything works fine...
View ArticleStatic Route to Null 0 for the Summary Address for OSPF
hi I am searching to do a lab about that topicdo you have some link interesting ?thanks
View Article1.1 Layer 2 Features - Why the QinQ?????
Hello All,could anyone explain to me why there is a need to configure QinQ in this task? We are tunneling "L3" etherchannel, for there is no tagging involved at the 2 ends. A simple tunneling should do...
View ArticleTask 6.2
Hi,I believe that you can either enable audit-trail globally or per inspection rule, so the following config would be valid : ip inspect name FIREWALL http audit-trail onip inspect name FIREWALL ftp...
View Article6.1 and 6.2 conflict
6.1 says to enable tcp and udp before blocking any ip packets to minimize impact.6.2 replaces the inbound acl(100) on R6 with a new acl (FROM_BB1). This new acl dosen't have a permit udp any any.
View ArticleClik here to view.
Nexus 1000v Installation Fails
Hi All,I was following the INE UCS videos (video20-24) whilst installing Nexus 1000v on my vCenter / ESXi host and got to video 23 about 15mins in when I tried to migrate the management port-group...
View Article6.3 Anyone get it working?
Hi,When I place the bridge group onto the interface even with an allow everything lsap filter all traffic for IP is dropped and therefore tears down BGP and v6 links.Anyone managed to get this solution...
View ArticleDecision to purchase DFE-580TX
Okay this is it !!! OWNERS of DFE-580TX please come forward and tell me if you can simulate router on the stick/QinQ scenarious (remember!!!this is 3 quad NIC dynamips setup) here is the card manual,...
View ArticleClik here to view.
OTV and vPC
Hello group, I’m looking for Information about OTV and vPC interaction. Basically I want to know if it ok to have the OTV extended Vlans and the OTV site Vlan to be trunked over the vPC link. Or if it...
View Articleworkbook volume I - initial ip address config
Hi to all,I purchase workbook volume I, from ine website i have donwloaded gns3 topology file, but i don't understand what ip addressing config i must load on GNS3. I started from the first lab on...
View ArticleHelp required in setting up lab
I have recently started prepration for CCIE R&S and want to build a dynamips/gns3 lab with real switches. I have two 3560 and two 3550 switches with EMI image. I am planning to buy PC with ASUS...
View ArticleSP WB v1.1
I've been going over this in my studies recently and was hoping someone might still have the dynamips topology file and the initial configs for the old v1.1 workbook for service provider. Please let...
View Article