WSA access issue
Anyone have successfully logged into the WSA?I'm trying to do the WSA initialization lab but can't get into the WSA.I can log in through the console but HTTP 8080 does not work. The WSA loaded with...
View Articlecrypto isakmp command error? CSR1000v image?
Hi,I am using image csr1000v-universalk9.03.12.00.S.154-2.S-std.ovaCisco IOS XE Software, Version 03.12.00.S - Standard Support ReleaseCisco IOS Software, CSR1000V Software...
View ArticleIOS NVI NAT
Dears,when using NVI NAT on cisco routers instead of regular NAT, can you please advise what is the difference between the below two commands:ip nat source static 1.1.1.1 2.2.2.2ip nat source static...
View ArticleNHRP redirect failed to initialise
Hello, I am doing some lab these days on DMVPN as i am preparing the RS v5 lab. I got this issu with GNS3 7200 router and latest IOS image c7200-adventerprisek9-mz.152-4.S5.bin.When I try to configure...
View ArticleASDM - monitor access only
Hi,I'm working now with WB section 'ASA local authentication' and I have one problem with ASDM read-only access. I checked documentation and I found:Â "The nas-prompt keyword allows access to the CLI...
View ArticleRouting to NBMA Interfaces
Hey everyone,Working through the v5 Workbook, and I'm on "Routing to NBMA Interfaces".Just wondering, if anyone could clarify the difference (if any) between using the following set of commands:Â Option...
View ArticleImpossible IPSec VPN Task
Hi,I know this is a bit off topic as it's more a security topic, but the principle is the same - its just a site-to-site ipsec tunnel.Anyway, I've been given an impossible ipsec vpn task by my manager...
View ArticleBGP AS-PATH list
Hi All,When I am looking in to the CCIE R&S V5 advanced technology lab "BGP Regular Expressions" I can able to see some routes are originating from AS 60 but AS60 is not configured anywhere. Can...
View Articleccie DC lab exam seat
Hiif any one interested to opt for ccie DC lab exam seat on July 9 Dubai location kindly let me know thanksÂ
View ArticleDDNS Configuration & Troubleshooting
G'day Everyone,I am kind of struggling here and really don't know where to turn to next and I was hoping if I threw my question amongst all you Cisco guru's you might be able to point me in the right...
View ArticleInitial config for a particular task
I am trying to do task 4.13 could not get it done...can anyone guide me that should I upload initial config of only that task and do as it is in the workbook as I did this also but still not getting...
View Article1000V Control Interface Port-Profile
So I've migrated everything (VMKs and VMs) to the 1000V with one exception - the Control interface on the VSM. When I attempt to migrate the interface to a 'standard' Veth PP, my VSM loses connectivity...
View ArticleAnnoying Difficulty Lab 4, 4.1
When I enable labeled unicast for R3 on XR1, I don't receive prefixes from R3 even with route-policy applied  neighbor 10.0.193.3 remote-as 2000   address-family ipv4 labeled-unicast...
View Articlebgp redist internal lab
I dont think this lab is correct. That is to say, I didn't need to redist internal on R3 in order to have full reachability to AS54 subnets from AS100 devices.
View ArticleRestricting access to your ESXi Virtual Rack
I have built a virtual rack using an ESXi server and now want to enable a few co-workers to use it. What options do I have to be able to allow one co-worker to access the rack at once?Currently I just...
View Articlebgp gre
I did this differently to the SG (but with same outcome)I created a gre tunnel and advertised the tunnel endpoints into the IGP. Then I created the r7/r8 ebgp peering over the tunnel directly....
View ArticlePPP, PPPoE and PPP authentication
Hello, I'm wondering why the PPP sections are missing from the workbook? The topics are still listed in the blueprint.Thanks.
View ArticleEIGRP Section DMVPN down on R5
I am going through the EIGRP section of the new V5 workbook and have got stuck at the first hurdle. All the network statements are on but between R2 and R5 DMVPN is not upR5#sh...
View ArticleUCS emulator connectivity issues
Has anyone successfully installed the USCPE ( emulator) Â on a MAC, version 10.9.2 ? Â Â I've been able to install the image in a virtual machine and configure from the command line, specifying the...
View ArticleLocal Web Authentication Using ACS
I couldn't get this lab working. Has anyone else had luck with it? I used the option 2 config per the lab and it doesn't seem to be working. ACS seems to only get some of the RADIUS authentication...
View Article