LAP 802.1x Authentication
I'm not getting why the LAP username is used in the ACS and dot1x authentication as well as lapuser authentication for the controller. Why are there two usernames for this? Is this because the AP...
View ArticleAutomatic reply: Are initial configs triggering some bug here?
Dear sender, I am out of office untill 18/04 , My substitute is Zied sassi (29535331). You can also send me SMS. Br.
View Article2.2
I have full connectivity apart from R2 pinging R4 & SW2 addresses (via R5). If I look in R2s RIB I can see it has the route information. I think the problem is related to the OSPF multipoint...
View ArticleBGP Regex Documentations
In the Configuration Guide, where is the bgp regex documentation? thanks
View ArticleCCIE ATC Sec videos about attacks
I'm currently watching some of the ATC 3.5 Sec videos. Brian has mentioned a few times "I'll show you more about the different attacks in a later video". Or "I'll show more about this topics in the...
View Article2.4 BGP Advertisements
Hello community,This task states that SW2 advertise VLAN28 and all RIP routes learned from BB2 into BGP, but at the moment SW2 is installing routes advertised by BB2 to its RIB via BGP due to AD of 20...
View ArticleINE's CCIE RSv5 Expanded Blueprint
INE's CCIE RSv5 Expanded Blueprint is meant to be used as a checklist that you can use as you go through your preparation.Click here to see INE's CCIE RSv5 Expanded Blueprint.
View ArticleClik here to view.
2.4
*Configure R2 so that all traffic destined for VLAN 29 comes in the Serial link to R3. I look at the SG and the config is all done on R5...
View ArticleCCIE RSv5 Equipment Build
Use this thread for Q&A on how to build INE's new CCIE RSv5 topology, either in physical hardware or virtualization. This thread will later be compiled into the new "How To Build A CCIE Rack" page.
View ArticleClik here to view.
BFD is such a PITA
I can't get BFD to work - it seems no matter where I try it, what I try it on, it just never works. It seems so easy in the DOCs ... I'm trying to get it working on four 3560X's running Version...
View ArticlePractice lab workbook access
Hi....I purchased the "Ultimate Security bundle" sometime late last year. Does this give me access to these workbooks? I am wondering if I need to purchase them seperately. Thanks
View ArticleClik here to view.
Traffic Redirection Question
Hi Everyone, Trying to think of how to achive this, check below picture and let me know of your ideas:- Hosts on Z1 can't tak to each other directly although in the same VLAN and have to go to the...
View ArticleAverage age of CCIE prospect's first lab attempt?
Hello all...just joined the forum and this is my first post...I am not sure if there are actual statistics showing the average age of prospective CCIE's first attempt, but I am about to retire from the...
View Articlespanning-tree portfast on interface enabled [do you agree?]
- spanning-tree portfast on interface enabledportfast--->immiedietely jump from blocking to forwarding state [omnit listening and learning]portfast--->don't block bpdu...
View Article[BGP]Update source and tcp server ?
Hi guys, I understood The usage of update-source command,but when i labed up a few things this is what i found outi)specifying update-source loop-back on one side is enough to from the peeringii)also...
View ArticleTask 5.3
I used for this task a different approach than the SG. I filtered the traffic with an extended ACL:ip access-list extended DROP_TTL_LESS_13 deny ip any 224.0.0.0 15.255.255.255 ttl lt 13 permit ip...
View ArticleINE CCIE v4 workbooks initial config
hi allI have INE CCIE rack in home, my question is about the initial config of the devices (not the backbone) for troubleshooting labs.because when you use INE rack rental you can load the configs !!...
View ArticleSCRACK4 ASA1 & ASA2 licenses are not the same
The active/standby configuration will not come up due to a license mismatch
View ArticleTask 2.8 Workbook II lab 18
I don't know if in the lab would be allowed but in this task i have bound a static default route to null0 interface on R5.That caused the advertising of an internal EIGRP default route without the use...
View ArticleASA 9.0 DMZ configuration question
hi everyone,this is the first ASA that I configure with the new 9.x (or 8.4 and above) version. I manage to get the DMZ to work, but i don't like my config at all. I will high-light what I struggle...
View Article