INE CCIE v5 material
Hello, would anyone know by chance if INE will be releasing new videos for the v5 format or just be remarking the v4 stuff as v5? OR will they release some after the v5 bootcamps have started? Just...
View ArticleBGP SoO
Hi. I have a question about BGP SoO. what is the need for using this Loop-prevention method in BGP, whereas, I think, the CE router will drop the updates received from PE router due to AS-Path loop...
View ArticleEthernet Overhead for Traffic Shaping
Hi Guys,Let's say I have the following policy:---------------------------------------policy-map ABC class class-default shape average 1000000interface FasthEthernet0/0 service-policy output...
View ArticleClik here to view.
Multipoint Frame-relay with virtual-template interface
i am unable to get route injected in R1, R2, R3, R4 routing table using Virtual-template interfaces.Can some one find the reason. Please find below topology and configuration and please comment thanks...
View Article13.20 - NAT with Route-Maps Solution Not Working
Hello community,I am wondering why R2 is not seing R5's replies when I ping 155.1.0.5 sourced from R2's loopback 0, yet R2 sees R3's replies and the configuration logic for both is exactly the...
View ArticleWorkbooks with TOC?
I'm sure this has been covered before, but is there a way to download the workbooks in a format with a table of contents currently? I'm sure I can find some copies in backup, but, regardless of that,...
View ArticleR&S v4.0 WB-1 9.24 IPv6 MP-BGP
Wondering why the network statement is not "Network 2003:1:0:11::/61? R1: interface Loopback 101 ipv6 address 2003:1:0:1::1/64 ! interface Loopback 102 ipv6 address 2003:1:0:11::11/61 ! router bgp 100...
View ArticleTCL srcipt for ping ip range in VRF
Hi,I would like to share a small script for pinging ip range in a vrf using tclsh in Cisco IOS.router(tcl)# for { set i 1 } { $i <= 100 } { incr i } { ping vrf TEST 10.10.10.$i re 5 }The above...
View Article2.4 IGP Redistribution
Hi All, Could someone explain me why in the solution of this task, AD of the redistributed RIP into the OSP domain is change to169?I do not see any reason why it has to be done as there is only one...
View ArticleR&S - May Lab Dates Available
A few weekend slots are open in May and on June 1st if anyone is in need.
View ArticleMPLS TE Bandwidth Contraints, MAM, RDM
Hi Guys,I am not sure if this has been disucssed but is it possible to get good documentation regarding the above topics? The workbooks do not touch them but perhaps the Brians or any other person...
View ArticlePPPoFR on multipoint interface question
Consider this simple setup:R1 102 ------ 201 R2 203 ------ 302 R3Here, PPPoFR is used to configure a common subnet 10.10.123.0/24 on R1, R2 & R3 with R2 being the hub. For each DLCI, it seems the...
View ArticleVPN Maps and Profiles
I'm a little confused about when and why to use different crypto elements. Can someone describe the evolution of static interface crypto maps to dynamic/static crypto profiles both for ISAKMP and...
View Article6.4
As ZBW/CBAC has been removed from v5 (and I dont intend to be taking the lab until July) I went with an ACL for this:ip access-list ex FILTERpermit icmp any any echo-replypermit icmp any any...
View Article4.1 L2 VC not comes up
Hi, I followed the SG and tunnel is up and I'm able to ping each others destination loo100 through tunnel int, also LDP neighbor comes up.However vc does not come up, my analysis says that label is not...
View Articlesomething I have noticed about the diff between wildcard and subnet
hi allsomething I have noticed about the different between wildcard address and the subnet mask address.regardless of the logic gates used,wildcard address is yes the inverse of subnet mask...
View ArticleASA pre 8.3 and 8.3+
Dears,I know that NAT differ between pre 8.3 and 8.3+ versions of Cisco ASA. Can i practice all other topics on a pre 8.3 ASA or there are other differences?Please advise,Moustapha
View ArticleCSC technology
Just started going through this and i can't shrug off the feeling that it is seems bit odd design in the real world, I would imagine most people would rather purchase a L2 service from the backbone...
View Articleme3600x qos enabled interface acting up
Hi everyone; just doscovered starnge issue. i am on a me 3600x. the client lan switch 9nexus 5k) is connected to gi0/1 on Me3600x. Customer has subscribed to a 300 meg wan service. wan interface...
View Article5.1 / 5.2
I used BSR for my PIM setup without issue (I noticed when looking at the PIM interfaces, they were all configured as sparse, so figured it saved me having to go around setting up pim rp addresses...
View Article